The two sources that matter
There are two kinds of figure in circulation. A thermal death point is the temperature at which bed bugs die quickly on exposure. Virginia Tech’s 2024 extension sheet gives them: “the thermal death point for bed bug adults and nymphs is 118°F degrees, but the thermal death point for bed bug eggs is 122°F.” It adds the part vendors leave out: “While bed bugs can be killed when exposed to slightly lower temperatures, (112–115°F), they have to consistently be exposed to these temperatures for a number of hours in order for death to occur.”
The second kind is a lethal temperature or time for 99% of a population, from the peer-reviewed study of commercial heat treatments by Kells and Goblirsch (University of Minnesota, Insects, 2011). Their LTemp99 was 48.3°C for adults and 54.8°C for eggs, which is 118.9°F and 130.6°F. At a lower holding temperature the time stretches out: at 45°C (113°F), adults needed 94.8 minutes for 99% mortality, and eggs needed 194.1 minutes to reach 50% and 428.5 minutes, over seven hours, to reach 99%.
| Figure | Adults and nymphs | Eggs | Source |
|---|---|---|---|
| Thermal death point | 118°F | 122°F | Virginia Tech ENTO-583NP (2024) |
| Lethal temperature, 99% (LTemp99) | 48.3°C / 118.9°F | 54.8°C / 130.6°F | Kells & Goblirsch (2011) |
| Time to 99% at 45°C / 113°F | 94.8 min | 428.5 min (194.1 min to 50%) | Kells & Goblirsch (2011) |
| Lower range, “a number of hours” | 112–115°F | Virginia Tech (2024) | |
| Room air during a treatment | about 135°F for four to five hours (VT); “may approach 55 to 65°C” = 131–149°F (UMN) | both | |
| Clothes dryer, hottest setting | at least 30 minutes, “will kill all life stages” | WA DOH 333-414 (March 2026) | |
The two egg numbers disagree, 122°F against 130.6°F, and we present both rather than pick the friendlier one. Our own standard is the stricter: every probe, including the one in the coldest crack, at or above 130°F for a sustained hold. The disagreement is also why “we got the room to 120” is not a treatment claim worth anything.
Why the room temperature is not the test
Virginia Tech, verbatim: “ambient temperature (the temperature of the heated air in the home) is not relevant! Bed bugs are not flying in the air, and the ambient temperature is no predictor of the temperature at floor-wall junctions, or the spaces underneath baseboards.” And: “these cracks and crevices must reach 122°F for the heat treatment to be effective. Many heat treatment technicians aim to get the ambient temperature up to 135°F and then leave the heaters in place for four to five hours.” The Minnesota authors say the same thing from the other direction: the air “may approach 55 to 65°C to ensure efficient mass transfer of heat” into the places the bugs actually are.
What the lower numbers mean in practice
The 113°F figure on some vendor pages is real, in the sense that the Minnesota study measured it. But at that temperature adults took an hour and a half and eggs over seven hours to reach 99% mortality, under controlled exposure, not in a box-spring corner the heaters reach last. The “hotter than 160 degrees” figure on another vendor page is not from any extension or journal source we can find. What matters is not the headline number but where it was measured and for how long.
What the Washington sources say
Neither the Washington Department of Health’s bed bug page nor WSU Extension’s fact sheet gives a heat-treatment temperature, which is why this site cites Virginia Tech and the Minnesota study for those figures. What the state does give is the dryer rule: the March 2026 DOH guidance says to “place affected items in a clothes dryer on the hottest temperature setting for at least 30 minutes. This will kill all life stages” (its general page says at least 20 minutes; the longer figure is the newer one). For anything you can put in a dryer, that is the whole answer.
The questions to ask any heat vendor
- How many temperature probes, and where? (“We watch the thermostat” is the wrong answer.)
- What probe temperature starts the hold, and how long is it? Do I get the log in writing?
- Do you offer a residual after the heat? Virginia Tech: “it makes sense to ask your (certified pest management) technician to apply a residual insecticide after the heat treatment is completed.”
Virginia Tech’s own warning closes it: “Not all bed bug heat systems are equally effective!” How our heat day runs →
Want the probe log, not the thermostat?
Call. We will tell you where the probes go before you book.
Call (253) 683-8516